[00:57:25] *** Quits: cyb3rkn19ht (~cyb3rkn19@pool-71-163-23-42.washdc.fios.verizon.net) (Read error: Connection reset by peer) [00:58:13] *** Joins: cyb3rkn19ht (~cyb3rkn19@pool-71-163-23-42.washdc.fios.verizon.net) [04:06:51] *** Quits: TheSeven (~quassel@rockbox/developer/TheSeven) (Quit: No Ping reply in 180 seconds.) [04:07:43] *** Joins: TheSeven (~quassel@rockbox/developer/TheSeven) [06:02:24] *** Quits: TheSeven (~quassel@rockbox/developer/TheSeven) (Disconnected by services) [06:02:32] *** Joins: [7] (~quassel@rockbox/developer/TheSeven) [06:55:31] *** Quits: cyb3rkn19ht (~cyb3rkn19@pool-71-163-23-42.washdc.fios.verizon.net) (Remote host closed the connection) [11:36:43] *** Joins: liar (~liar@clnet-p09-185.ikbnet.co.at) [12:13:18] *** Quits: liar (~liar@clnet-p09-185.ikbnet.co.at) (Read error: Connection reset by peer) [12:14:52] *** Joins: liar (~liar@clnet-p09-185.ikbnet.co.at) [15:16:01] *** Joins: Kashinoda (~Kashinoda@host86-157-213-219.range86-157.btcentralplus.com) [15:16:51] Any support people alive? [15:18:31] I had previously installed emCore on a 160GB classic without a problem [15:19:01] I've tried again on another classic (6th gen, 120gb) and when it loads up I receive the error [15:19:03] "emCORE v0.2.3 r859 [15:19:03] ATA: Error 80000003 while reading BBT (sector 0, count 1)" [15:19:21] won't go past it, everytime I switch it on the same error occurs [15:22:20] sounds like hdd failure [15:22:32] it can't read the very first sector of the HDD [15:22:41] [7] might have an idea how to fix it [15:23:05] Thanks for the reply [15:23:23] okay, I'll wait around for him :) [15:23:47] I had a HDD error with the last iPod I used emCore on, but was able to just use the second half of the hard drive with healthy sectors [15:23:57] I can't even get to the point to format this one obviously [15:26:58] *** Joins: Viso (32a36cdb@gateway/web/freenode/ip.50.163.108.219) [15:27:55] I am experiencing difficulty installing Rockbox on iPod Classic. [15:29:53] According to , I should be able to run "sudo python libipoddfu.py bootstrap-ipodclassic-r859-20120102.dfu" and get a UMSBoot screen to show on the iPod. [15:30:23] The iPod does not appear to respond to this command. [15:31:53] Previously, I had successfully obtained the boot screen, but received various errors in copying a .ubi file to the device. The system said the device was full, despite the GUI showing an empty 67MB volume. [16:25:55] *** Quits: Viso (32a36cdb@gateway/web/freenode/ip.50.163.108.219) (Ping timeout: 250 seconds) [18:14:20] *** Joins: [Saint_] (~saint@rockbox/user/saint) [18:14:20] *** Quits: [Saint] (~saint@rockbox/user/saint) (Disconnected by services) [23:20:06] <[7]> Kashinoda: yes, sector 0 (which contains the partition table) seems to be damaged on your ipod, or there is some other problem accessing the disk